iE 250 Application SW (Flexible application)
您即将下载 iE 250 Application SW (Flexible application)
您已选择下载我们的软件。
几秒钟内,您将收到一封包含下载链接的电子邮件。
如果使用软件有问题,请联系support@deif.cn.
诚挚的祝福,
DEIF A/S
本软件受DEIF A/S版权保护。请点击上述链接可查阅DEIF A/S版权和许可协议(EULA)。
本软件适用于以下DEIF产品
您即将下载 2.0.9.0
与上一版本相比,主要更新如下:
2.0.9.0 based on 2.0.8.1
New features
- Three pump logic routines can now be set up to control the pumping of a substance.
- Implement ECU diagnostic to enable run coil and ECU power while the engine is stopped.
- All configuration dependent values are now possible to use in the flexible Modbus.
Changes
- Modbus timeout increased from 10 sec to 100 sec on iE 250 and iE 350.
- Number of possible Modbus connections changed from 20 to 100 on iE 250 and iE 350.
- EIC: Volvo Penta EMS2.4: "Engine Override Control Mode" changed to "Speed control".
- EIC: Volvo Penta EMS2.4: TSC1 will not be transmitted if VP70 is used for regulation.
- Added write permission for "Priorities" when the controller is in emulation.
Corrections
- Fixed issue where changes made in the UI were not registered.
- Fixed issue where the "IO configuration" menu would show empty slots.
- Fixed issue where tree-structure menu groups could not be collapsed using touch.
- Fixed issue where iE 250 failed to start up without MIO module.
- Fixed issue where configuring a Modbus value to "true" made the value "255" instead of "1".
- Fixed issue where measurements from multiple ECUs were not shown in UI for e.g. configuring alarms.
- Fixed issue where display user could not clear DM2 logs.
- Fix issue where iE controller could not start without MIO module.
- Fixed issue with missing alarm icons.
- Fixed issue where user could enter parameter values outside of valid range.
- Fixed checksum and counter for VP70.
- Fixed issue where PIM2.1 DIO levels were inverted.
- Fixed issue where removing network cable would activate system NOK, IO service error and "temperature too high" alarms.
- Fixed issue where CODESYS user management files were not included in backup/restore.
- Fixed issue where linked outputs in CODESYS were hidden in the IO configuration.
- Fixed issue where PWM was not working on MIO2.1.
- Fixed issue where Genset was not deloading correctly when it was connected to mains.
- Fixed issue where BUS TIE breaker could not deload and open a ring connected busbar.
版本号 | 发布日期 | 描述 |
---|---|---|
2.0.9.0 |
04/05/2025 |
2.0.9.0 based on 2.0.8.1New features
Changes
Corrections
|
2.0.8.1 |
10/02/2025 |
Corrections
Changes
|
2.0.8.0 |
17/01/2025 |
2.0.8.0 based on 2.0.6.0 New features
Changes
Corrections
|
在此页面,您可以下载产品的更新软件,并使用各种实用工具和附加组件设置、检测故障和配置产品。
请注意,用户无法更新我们的所有产品。同时也不是所有产品都配有实用工具。因此,本页的软件列表不能视为DEIF产品的概述。
DEIF将登记您注册的下载邮箱地址,以便在未来需要时发送有关的更新信息。
DEIF不对产品更新失败或使用实用工具造成的任何后果负责。DEIF A/S也不对软件升级导致的产品行为变化的后果负责。用户始终有责任在调试前确保正确的设置和配置。请在更新产品之前查阅软件的更新日志。
www.deif.cn软件下载许可协议
下载的软件仍是DEIF的财产。本软件不得用于商业目的分发, 不得全部或部分更改或重复使用,也不得出售给任何第三方。
最新版本,功能齐全
我们始终建议您安装最新版本的软件,以充分利用您的DEIF产品。
所有更新的软件都可以从www.deif.cn->支持->下载->软件栏目下下载。
如果您在查找产品的相关软件时有任何疑问或问题,请随时致电丹控电气(上海)有限公司,电话: +86 21 68796200,或者发送电子邮件至support@deif.cn, 我们随时为您服务。