SGC 120 MkII Firmware
您即将下载 SGC 120 MkII Firmware
您已选择下载我们的软件。
几秒钟内,您将收到一封包含下载链接的电子邮件。
如果使用软件有问题,请联系support@deif.cn.
诚挚的祝福,
DEIF A/S
本软件受DEIF A/S版权保护。请点击上述链接可查阅DEIF A/S版权和许可协议(EULA)。
本软件适用于以下DEIF产品
您即将下载 R16.00
与上一版本相比,主要更新如下:
New features
- Added 0-5V sensor selection for pin 23.
- Added Custom Sensor.
- Added Activation & Delay for Custom Sensors.
- EIC: Added support for Baudouin Gas.
- EIC: Added support for Baudouin Wise10B.
- EIC: Added support for Caterpillar ADEM 6.
- EIC: Added support for Deutz EMR 5 Stage V.
- EIC: Added support for Doosan Stage V.
- EIC: Added support for Generic CPCB IV.
- EIC: Added support for Isuzu.
- EIC: Added support for Iveco Stage V.
- EIC: Added support for JCB.
- EIC: Added support for JCB 430/448 Stage V.
- EIC: Added support for Jichai JC15D Weifu.
- EIC: Added support for Jichai JC15T JG.
- EIC: Added support for Jichai JC190.
- EIC: Added support for Jichai WYS.
- EIC: Added support for Jing guan.
- EIC: Added support for John Deere.
- EIC: Added support for John Deere Stage V.
- EIC: Added support for Kohler.
- EIC: Added support for MAN.
- EIC: Added support for MAN EMC Step 2.0.
- EIC: Added support for MAN EMC Step 2.5.
- EIC: Added support for Perkins CPCB IV.
- EIC: Added support for Perkins Stage V 120xJ.
- EIC: Added support for PSI.
- EIC: Added support for Scania EMS2 S6.
- EIC: Added support for Weichai Diesel.
- EIC: Added support for Weichai e6gas.
- EIC: Added support for Weichai Gas.
- EIC: Added support for Weichai Wise10B.
- EIC: Added support for Weichai Wise15.
- EIC: Added support for Yuchai.
- EIC: Added support for Generic CPCB4 +.
- Added Auto Load Transfer In Manual for Mains as a separate parameter.
- New Data added over Modbus.
Changes
- Interlock of breaker feedback added as an interlock for Contactor latching of Generator and Mains.
- The breaker on the display now mimics the contractor feedback.
- Limited Counter Reset removed. The user can now reset any change multiple times with a password.
版本号 | 发布日期 | 描述 |
---|---|---|
R16.00 |
15/10/2024 |
New features
Changes
|
R15.00 |
24/04/2024 |
New feature• New engine protocol added: |
R14.01 |
11/12/2023 |
SGC 120 Mk ll offline firmware initial release. R12.00 was the initial release for the SGC Mk ll variants. All previous releases were over smart flash. New feature:• Config and M-Logic flashing in live mode.
Changes:• Updated start sequence to avoid breaker closure before safety monitoring expires. |
在此页面,您可以下载产品的更新软件,并使用各种实用工具和附加组件设置、检测故障和配置产品。
请注意,用户无法更新我们的所有产品。同时也不是所有产品都配有实用工具。因此,本页的软件列表不能视为DEIF产品的概述。
DEIF将登记您注册的下载邮箱地址,以便在未来需要时发送有关的更新信息。
DEIF不对产品更新失败或使用实用工具造成的任何后果负责。DEIF A/S也不对软件升级导致的产品行为变化的后果负责。用户始终有责任在调试前确保正确的设置和配置。请在更新产品之前查阅软件的更新日志。
www.deif.cn软件下载许可协议
下载的软件仍是DEIF的财产。本软件不得用于商业目的分发, 不得全部或部分更改或重复使用,也不得出售给任何第三方。
最新版本,功能齐全
我们始终建议您安装最新版本的软件,以充分利用您的DEIF产品。
所有更新的软件都可以从www.deif.cn->支持->下载->软件栏目下下载。
如果您在查找产品的相关软件时有任何疑问或问题,请随时致电丹控电气(上海)有限公司,电话: +86 21 68796200,或者发送电子邮件至support@deif.cn, 我们随时为您服务。