Multi-line 2 BGC Application Software series 1.x.

您即将下载 Multi-line 2 BGC Application Software series 1.x.

您已选择下载我们的软件。

几秒钟内，您将收到一封包含下载链接的电子邮件。

如果使用软件有问题，请联系support@deif.cn.

诚挚的祝福，

DEIF A/S

本软件受DEIF A/S版权保护。请点击上述链接可查阅DEIF A/S版权和许可协议(EULA)。

本软件适用于以下DEIF产品

您即将下载 1.10.3

与上一版本相比，主要更新如下：

Changes:

  • Update of self-check functionality
版本号 发布日期 描述

1.10.3

15/05/2015

Changes:

  • Update of self-check functionality

1.10.2

23/02/2007

Changes:

  • Menu for Voltage Trip (Phase-Phase or Phase-Neutral) removed.

1.10.1

21/02/2005

Changes:

  • Handling of MB in VDE0108 AUS mode updated.
  • Rampdown updated.
  • Returning from JUMP menu sets to main view.
  • Mode "Load take over" updated.
  • Digital input alarm handling updated.
  • Emergency stop default set to OFF.

1.10.0

07/02/2005

Changes:

  • Setting if WARNING fail class should autoreset or not added
  • Analogue input readings optimised for better precision
  • Alarm acknowledge updated for option VDE0108
  • Factory settings of var export/import changed
  • interface to USW regarding inputs optimised
  • Analogue input board (option M15) reading optimised
  • Test mode updated

1.05.0

05/01/2005

Changes:

  • When breaker position is unknown, breaker LED will be flashing red.
  • Now possible to open GB in Island SEMI when Loadshare not present and breaker alarms active.
  • Ramp down added to TEST mode.
  • GB opens immediately in MAN mode when activated.
  • RPM max. settings changed from 2000 to 4000. Overspeed alarms corrected according to this. Improved handling when using external power setpoint.
  • Password to changing password changed. Must use master password level to change master password. Must use OEM password level to change OEM password.
  • In VDE0108 alarm horn is now set off when first alarm of multiple alarms is acknowledged.
  • Display is updated when using binary input for alarm acknowledge

1.04.5

12/11/2004

Changes:

  • Governor and AVR offset function modified

1.04.4

19/10/2004

Changes:

  • Manual stop in AUTO mode is changed
  • Test mode handling changed
  • Handling of other languages than English is changed

1.04.2

01/09/2004

Changes:

  • Handling of mains breaker supervision when using contactor setting changed to avoid alarm when combined with zero-voltage coil trip of mains.

1.04.1

02/08/2004

Changes:

  • Gen-set will ramp up in TEST mode.
  • Underlined characters of extended ASCII-table added.

1.04.0

28/06/2004

Changes:

  • USW interface improved
  • Reset regulation functionality adjusted
  • Settings possibilities for Emergency stop-menu extended
  • Handling of GB and MB modified

1.03.1

09/03/2004

Changes:

  • Manufactor name for CAN-open option changed
  • Option H4 - minor chnnges
  • USW interface regarding GB and MB extended
  • Alarm inhibit functionality changed during stop-sequence
  • Short circuit protection functionality changed
  • Failclass 'Warning' functionality improved
  • Functionality of frequency and voltage acceptance detection changed
  • Check of language added to USW control
  • GSM option menu extended
  • Service timers functionality added to USW
  • Event log update functionality changed
  • GB feedback handling changed
  • Single running in Island-mode functionality changed
  • Running hour calculation improved

1.03.0

11/02/2004

New features:

  • Modeshift can now be controlled with digital input or menu 4440
  • Stop mode in menu 4900 added
  • Option for support of VDE0108 is added
  • GB position error can be deactivated (digital configurable input set to 'not used')
  • Kvarh (import / export) counter added
  • Sprinkler-mode functionality changed to include Short circuit 1,2
  • Start attempt counter added
  • New menu for number of sprinkler start attempt is added
  • 'Load take over'-mode added
  • Emergency power relay output added
  • Collective fault output added
  • 'Ready for operation' functionality added
  • Possibility for activation of Test mode with conf. digital input added
  • Possibility for 2 X option M13 or M14 added
  • SMS module updated with ID number in every message
  • SMS module updated with alarmbuffer, all alarms will now be sent
  • Modbus communication is optimised

Changes:

  • SMS module is stopped if no phone-numbers are used
  • CCM communication is optimised
  • W_L menu and functionality removed
  • Static charger menu and functionality removed
  • Voltage level for running detection changed
  • Timing changed, if modeshift is on and mains failure occur
  • 'Peak current' renamed for 'Short circuit'
  • H4 option shown in USW
  • If a mains fail occurs during TEST mode the AMF sequence will start
  • USW stop command optimised
  • Static sync improved function
  • Improved power factor calculation
  • Password handling optimised
  • Menu handling in regard to Option A1 A2 A3 optimised
  • Default setting for secondary value for current trafo's for Generator and busbar changed
  • Counter handling (hours, CB, MB operations) optimised
  • Deload is interrupted if remote start/stop is changed from start -> stop -> start
  • MB operations optimsed during change of configuration
  • Function of Relay 13 optimised
  • Menu handling in regard to loadshare PCB optimised
  • Menu handling for Option M13 optimised
  • Possibility for Test-mode in Island mode removed
  • Mains-failure detection improved
  • Start enables functionality improved
  • Log-functionality improved
  • Failclass handling in auto mode optimised

1.01.2

07/11/2003

Changes:

  • Security regarding write/erase operation in boot-sector is improved.

1.01.1

10/10/2003

Changes:

  • The 8 Start/stop menus are adjusted
  • Menu 4250, 'ID BAUD' -> 'TYPE' corrected

1.01.0

03/10/2003

New features:

  • Can-Open support enabled
  • 'JDEC' engine communication added

Changes:

  • Line 3 adjusted when 'mode button' is used
  • Eventlog secured when power up less than 3sec
  • Frequency measurement below 20Hz is disabled due to a problem under stopping the gen-set.  This could in rare cases generate a reset of the unit.
  • Timing in case of 'MB trip externt' adjusted

1.00.4

29/08/2003

Changes:

  • Changed max limit in menu 1290 1300 from 300% -> 350%
  • Changed text string for 2180 + 2190 (Deadband - > limit)
  • Removed PF control settings, not used

1.00.3

01/08/2003

New features:

  • Option H4 CCM Caterpiller

Changes:

  • SMS phonenumber-interface to USW adjusted
  • Peak-current measurement improved
  • dfdt and vector-jump function improved
  • Stop of gen-set if mains-fail is added
  • Energy counters added

1.00.2

01/07/2003

New features:

  • Possibility to configure input for Alarm Acknowledge added
  • Possibility to configure input for Alarm Inhibit added
  • Possibiblity for activating fuel-logic

Changes:

  • Close of MB in auto changed
  • Text changed: 'Sprinker' -> 'Fire pump'
  • Generator protection moved into Option C1
  • Display update sequence optimized
  • VDO-input for fuel-logic is optimized

1.00.0

30/06/2003

Initial release

在此页面，您可以下载产品的更新软件，并使用各种实用工具和附加组件设置、检测故障和配置产品。

请注意，用户无法更新我们的所有产品。同时也不是所有产品都配有实用工具。因此，本页的软件列表不能视为DEIF产品的概述。

DEIF将登记您注册的下载邮箱地址，以便在未来需要时发送有关的更新信息。

DEIF不对产品更新失败或使用实用工具造成的任何后果负责。DEIF A/S也不对软件升级导致的产品行为变化的后果负责。用户始终有责任在调试前确保正确的设置和配置。请在更新产品之前查阅软件的更新日志。

www.deif.cn软件下载许可协议

下载的软件仍是DEIF的财产。本软件不得用于商业目的分发, 不得全部或部分更改或重复使用，也不得出售给任何第三方。

最新版本，功能齐全

我们始终建议您安装最新版本的软件，以充分利用您的DEIF产品。

所有更新的软件都可以从www.deif.cn->支持->下载->软件栏目下下载。

如果您在查找产品的相关软件时有任何疑问或问题，请随时致电丹控电气(上海)有限公司，电话: +86 21 68796200，或者发送电子邮件至support@deif.cn, 我们随时为您服务。

更多信息