Multi-line 2 ASC Application Software series 4.x
您即将下载 Multi-line 2 ASC Application Software series 4.x
您已选择下载我们的软件。
几秒钟内,您将收到一封包含下载链接的电子邮件。
如果使用软件有问题,请联系support@deif.cn.
诚挚的祝福,
DEIF A/S
本软件受DEIF A/S版权保护。请点击上述链接可查阅DEIF A/S版权和许可协议(EULA)。
本软件适用于以下DEIF产品
- ASC-4 储能控制器 - 自动可持续能源控制器
- ASC-4 太阳能控制器 - 自动可持续能源控制器
- ASC-4 储能单机控制器 - 全自动可持续储能控制器
- ASC-4 太阳能单机控制器 - 自动可持续能源控制器
您即将下载 4.25.0
与上一版本相比,主要更新如下:
PM compatibility version 1.29.0
New features:
- Added support for DEIF MIB 8000 power meter.
- Added support for Eastron Smart X96 power meter.
- Added support for EPC Power PCS protocol.
- Added parameter 2810 to the ASC-4 Battery. It can be used to configure a timeout period after the last transmitted heartbeat signal before the PCS activates an error (only for supported ESS protocols).
- Added parameters 2805 and 2806. The parameters support an adjustable offset to the droop curves used for the delta frequency and delta voltage calculations when a DG or a mains is connected.
- Added Jinko PCS protocol.
- Added BMSer Technology BMS protocol.
- Added Narada w Ctrl BMS protocol.
- Added support for Dynapower CPS-1500 PCS protocol.
- Added a new M-Logic output and event. This is to give the user the option to manually activate boost charging in supported systems.
- Added parameters 8201, 8202 and 8203 to set a PDS spinning reserve value. This sets the percentage of produced PDS power that should be reserved locally as extra available battery discharge capacity.
- Added SICON PCS protocol.
- Added support for Gold BMS protocol.
Changes:
- Sungrow LC100 Utility LFP and STxxxCP50-HV ESS protocols now use delta frequency and voltage regulation when operating in VSG on-grid mode.
- Updated the Ausar MAE ESS protocol to support version A04.
- Removed the pulse input counter configuration parameters from the display and USW.
- Added +25 kV scaling on ASC-4. This includes adding 2 scaling levels 10 kV to 250 kV and 0.4 kV to 75 kV.
Corrections:
- Corrected missing three-phase power calculation in Danfoss Vacon ESS monitoring values.
- Corrected an issue where a battery would still try to charge fully from a PV that was de-loading to stop.
- Corrected calculation of frequency set point for ESB sync.
- Corrected an issue where a battery would stop in a PMS auto application if the internal mode of the ASC was set to "No dispatch" instead only offloading when other voltage sources was connected to the busbar.
- Corrected calculation of discharge capacity of the Powercube BMS protocol.
版本号 | 发布日期 | 描述 |
---|---|---|
4.25.0 |
09/02/2023 |
PM compatibility version 1.29.0 New features:
Changes:
Corrections:
|
4.24.0 |
24/11/2022 |
PM compatibility version 1.28.0 New features:
Changes:
Corrections:
|
4.23.1 |
15/09/2022 |
PM compatibility version 1.25.0 Corrections:
|
4.23.0 |
31/08/2022 |
PM compatibility version 1.25.0 New features:
Changes:
Corrections:
|
4.22.0 |
03/05/2022 |
PM compatibility version 1.25.0 New features:
Changes:
Corrections:
|
4.21.0 |
18/02/2022 |
PM compatibility version 1.25.0 New features: Changes: |
4.20.0 |
09/12/2021 |
PM compatibility version 1.24.2 New features:1- Sungrow LC100 BCU protocol added. Changes:1- Renamed "Ginlong Solis" PV protocol to "Solis (Ginlong)". |
4.19.0 |
22/11/2021 |
PM compatibility version 1.24.2 New features:
Changes:
Corrections:
|
4.18.0 |
20/09/2021 |
PM compatibility version 1.24.1 New features:
Changes:
Corrections:
|
4.17.1 |
16/07/2021 |
PM compatibility version 1.24.1. Corrections:1- Corrected that the EVVO PV protocol did not send control telegrams to control the active power of the inverter. |
4.17.0 |
28/06/2021 |
PM compatibility version 1.24.1. New features:
Changes:
Corrections:
|
4.16.0 |
08/04/2021 |
PM compatibility version 1.23.0. New features:
Changes:
Corrections:
|
4.15.1 |
25/02/2021 |
PM compatibility version 1.22.0. Corrections:
|
4.15.0 |
30/11/2020 |
PM compatibility version 1.22.0. New features:
|
4-14-2 |
29/10/2020 |
PM compatibility version 1.20.0 Corrections:
|
4.12.0 |
19/03/2020 |
PM compatibility version 1.16.0. New features:
|
4.11.3 |
28/01/2020 |
PM compatibility version 1.16.0 Corrections:
|
4.11.2 |
24/01/2020 |
PM compatibility version 1.16.0 Corrections:
|
4.11.1 |
31/10/2019 |
PM compatibility version 1.16.0. Corrections:
|
4.11.0 |
11/12/2018 |
PM compatibility version 1.16.0 New features:
Corrections:
|
4.10.1 |
16/04/2018 |
Corrections:
|
4.10.0 |
20/03/2018 |
PM compatibility version 1.16.0 New features:
Corrections:
|
4.05.2 |
12/01/2018 |
Corrections:
|
4.05.1 |
02/01/2018 |
PM compatibility version 1.15.0
|
4.05.0 |
30/11/2017 |
PM compatibility version 1.15.0 New features:
Corrections:
Changes:
|
4.04.0 |
05/10/2017 |
PM compatibility version 1.15.0 New features:1- Support of HiQ inverter. |
4.03.1 |
09/05/2017 |
PM compatibility version 1.15.0 Corrections:
|
4.03.0 |
03/04/2017 |
Version 4.03.0 New features:
Changes:
Corrections:
|
4.02.0 |
21/12/2016 |
PM compatibility version 1.15.0 New features:
Changes:
Corrections:
|
在此页面,您可以下载产品的更新软件,并使用各种实用工具和附加组件设置、检测故障和配置产品。
请注意,用户无法更新我们的所有产品。同时也不是所有产品都配有实用工具。因此,本页的软件列表不能视为DEIF产品的概述。
DEIF将登记您注册的下载邮箱地址,以便在未来需要时发送有关的更新信息。
DEIF不对产品更新失败或使用实用工具造成的任何后果负责。DEIF A/S也不对软件升级导致的产品行为变化的后果负责。用户始终有责任在调试前确保正确的设置和配置。请在更新产品之前查阅软件的更新日志。
www.deif.cn软件下载许可协议
下载的软件仍是DEIF的财产。本软件不得用于商业目的分发, 不得全部或部分更改或重复使用,也不得出售给任何第三方。
最新版本,功能齐全
我们始终建议您安装最新版本的软件,以充分利用您的DEIF产品。
所有更新的软件都可以从www.deif.cn->支持->下载->软件栏目下下载。
如果您在查找产品的相关软件时有任何疑问或问题,请随时致电丹控电气(上海)有限公司,电话: +86 21 68796200,或者发送电子邮件至support@deif.cn, 我们随时为您服务。