Multi-line 2 Standard Application Software series 2.3x and 2.4x 2.31.2

您即将下载 Multi-line 2 Standard Application Software series 2.3x and 2.4x 2.31.2

您已选择下载我们的软件。

几秒钟内，您将收到一封包含下载链接的电子邮件。

如果使用软件有问题，请联系support@deif.cn.

诚挚的祝福，

DEIF A/S

本软件受DEIF A/S版权保护。请点击上述链接可查阅DEIF A/S版权和许可协议(EULA)。

本软件适用于以下DEIF产品

您即将下载 2.31.2

与上一版本相比，主要更新如下：

Changes:

  • Handling of asynchron generator changed
  • Option O - regulators for water-turbines adjusted
  • Minor changes to menus and min/max settings
版本号 发布日期 描述

2.31.2

04/03/2005

Changes:

  • Handling of asynchron generator changed
  • Option O - regulators for water-turbines adjusted
  • Minor changes to menus and min/max settings
版本号 发布日期 描述

2.42.8

30/03/2015

This software applies to the following DEIF products:

  • Multi-line 2 - GPC v.2.xx
  • Multi-line 2 - GPU v.2.xx
  • Multi-line 2 - PPU v.2.xx

Change:

  • Update of self-check functionality

2.42.7

19/09/2011
  • Running hour counter overflow at 32500hours corrected.

2.42.6

27/04/2011
  • Analogue output (option F2) improved.

2.42.5

24/02/2010
  • Removed bumb from regulator first time GB closes.

2.42.4

22/10/2009
  • Df/dt protection improved.
  • Vector jump protection improved.
  • Unit psi implemented for analog input

2.42.3

20/03/2009
  • Writing to control registers no longer depends on H options.
  • Low current measurements improved.
  • Handling of synchronizing failure improved
  • Parameter 2260 is now available in DEIF Utility Software.
  • Ability to show large negative power improved.
  • Maximum timer values for stop failure and run status set to 3000 seconds.
  • Unbalanced current calculations now relates to the nominal current setting.
  • New modbus measurement (03h) at address 65 indicates PF with sign. Address 11 is without sign.

2.42.2

23/11/2007
  • Sync. using step up transformer improved.

2.42.1

29/10/2007

New features:

  • Protection level "Over load 3" added.

Changes:

  • "No Regulation" was logget twice.
  • Password max limit changed to 32000.
  • kWh counter output did not work correct after reset of counter value.

2.42.0

31/08/2007

New features:

  • Ramp up in loadshare mode.

Changes:

  • USW did not show password correct if language other than English was selected

2.41.2

25/05/2007
  • Improved frequency protection.

2.41.1

08/05/2007

Changes:

  • Max setting for starter ON time 180s.
  • Improved alarm log handling.
  • Improved vector jump calculation.
  • Show terminal 43 - 53 at USW only if load share board is present.
  • Could not access menu 4960 via jump.
  • USW did not show menu 2275.
  • Unbalance voltage calculations improved.
  • Zero sequence calculations improved.

2.41.0

23/10/2006

Changes:

  • EF5 option implemented
  • Handling of option M15 changed
  • Inhibit of BB alarms U>, f>

2.40.1

03/10/2006

Changes:

  • Accuracy of reactive power measures improved
  • Accuracy of I>> measure improved

2.40.0

18/08/2006

New features:

  • Use of step-up transformer. 

2.32.6

27/04/2006

Changes:

  • Possibility to set option G1 modified

2.32.5

08/03/2006

Changes:

  • Option O1, cascade control has been trimmed

2.32.4

02/01/2006

Changes:

  • Analogue output for PF modified
  • Interface between USW and GPU settings modified
  • Menu's for M13 modified
  • Handling of relay 10...13 modified
  • MDEC protocol handling modified
  • GPU - relay-functionality modified

2.32.2

10/10/2005

Changes:

  • Handling of option C2 - alarms during genset stop sequence changed
  • Scaling of the controller output shown in the USW changed
  • Mode-handling via terminal 43 is changed
  • Handling of downloading changed parameters changed
  • Option O handling of waterlevel controller changed
  • Factory settings for negative + zero sequence changed

2.32.1

27/06/2005

Changes:

  • Water-level regulation updated

2.32.0

30/05/2005

New features:

  • CanOpen protocol: Zero-sequence U and I failure added

Changes:

  • RPM measurements updated
  • Option O - regulator start adjusted
  • Minor changes in menus and min/max settings

2.31.2

04/03/2005

Changes:

  • Handling of asynchron generator changed
  • Option O - regulators for water-turbines adjusted
  • Minor changes to menus and min/max settings

2.31.1

14/12/2004

Changes:

  • Relay3 functionality regarding alarm/reset adjusted
  • Volvo Penta engine protocol adjusted
  • Minor changes in menu texts

2.31.0

24/11/2004

New features:

  • SMS functionality extended
  • Option H5 - MDEC engine interface extended
  • Splitphase/single functionality modified
  • Limit switches functionality extended

Changes:

  • Relay output functionality extended
  • Analogue current output for AVR/Gov limited
  • GDU interface adjusted
  • Some menus in some languages adjusted
  • Some minor adjustments of set-points limits

2.30.3

12/08/2004

Changes:

  • Handling of The emergency stop functionality in regard to option M20 is changed
  • Reverse power alarm - max timer setting is extended
  • Alarm messages displayed in USW is now displayed in the chosen Multi-line 2 language
  • German texts are adjusted
  • The Modbus ASCII mode is improved
  • Eventlog view in USW is improved
  • Update of number of CB operations is changed
  • Negative sequence voltage functionality improved at high voltages
  • Possible overflow in scaled analogue input is removed

2.30.1

15/06/2004

Changes:

  • Frequency regulator adjusted for perfect performance
  • Initialisation of loadshare lines are optimised
  • Run coil functionality adjusted

2.30.2

15/06/2004

Changes:

  • Option H4 CCM: Optimised and extended possibilities
  • Modbus possibilities extended 
  • Translations of German and Spanish completed

2.30.0

14/04/2004

New features:

  • Option H4 CCM-communication read/write functions extended
  • Option H4 CCM-comminication heartbeat handling added
  • Option H5 Can-bus Engine interface implemented, supporting:
    MDEC 2000/4000 M.302
    MDEC 2000/4000 M.303
    DDEC
    EMR 
    JDEC
    Volvo Penta
  • Option H6 Cummins engine communication added
  • Modbus protocol extended

Changes:

  • Running detection for disconnection of starter is changed
  • Configurable display text for PT100 added
  • Some setpoint ranges are extended
    Option O Waterturbine - minor changes of functionality

2.20.1

11/02/2004

Note: When updating a previously version of the application software, which is using the engine start/stop logic, with this new version (2.20) will requirre enabling of engine start/stop logic after software updating. Default the engine start/stop logic is disabled after updating the software. To enable it jump to menu 6030 and activate the engine start/stop logic - not as previously stated menu 6000.

New features:

  • GSM Modem connection supported
  • Automatic transmission of SMS in case of an alarm
  • Voltage transformer ratios different for generator and busbar supported
  • Display texts configurable for readings as well as alarms
  • Selection of monitoring of phase-phase or phase-neutral voltages
  • Counters for kWh export, kWh import, kvarh export and kvarh import on Modbus.
  • Option M20 added. Engine I/F boards with or without engine start/stop logic selection. 
  • Dual alarm settings for all analogue values (4-20 mA, PT100, VDO, RPM)
  • Modbus ASCII mode added
  • Catarpillar PWM output improvements regarding regulator setting
  • Zero sequence alarms for voltage and current
  • Possible to check version of basis software
  • Serial modbus communication optimised

Changes:

  • ML2 will send a login string when a CCM-comm. string is created
  • 2nd parameters for some alarms are changed
  • Alarms can be ack. via Comm regardless of the External comm. control input.
  • Option O - water turbine is adjusted
  • PF readout in display is adjusted
  • Scaling in the USW on some points are adjusted
  • Conditions for Mode 3 is adjusted
  • Conditions for manual mode are adjusted
  • Cooperation between Option D1 and Option O together with option E1 or EF4 is adjusted
  • Menu selection with Option EF4 is adjusted
  • Menu selection with Option EF3 is adjusted
  • High overcurrent adjusted in regard to settings.
  • Parameter index for CANopen option adjusted

Note: When updating a previously version of the application software, which is using the engine start/stop logic, with this new version (2.20) will requirre enabling of engine start/stop logic after software updating. Default the engine start/stop logic is disabled after updating the software. To enable it jump to menu 6000 and activate the engine start/stop logic. 

END-USER LICENSE AGREEMENT (“EULA”) FOR DOWNLOADABLE SOFTWARE. (“the SOFTWARE PRODUCT”).

IMPORTANT: PLEASE READ THE TERMS AND CONDITIONS OF THIS LICENSE AGREEMENT CAREFULLY BEFORE CONTINUING WITH THIS PROGRAM INSTALL:

 

DEIF A/S End-User License Agreement ("EULA") is a legal agreement between you (either an individual or a single entity) and DEIF A/S for the DEIF A/S software product(s) identified above which may include associated software components, media, printed materials, and "online" or electronic documentation. By installing, copying, or otherwise using the our product, you agree to be bound by the terms of this EULA. This license agreement represents the entire agreement concerning the program between you and DEIF A/S, (referred to as "licenser"), and it supersedes any prior proposal, representation, or understanding between the parties. If you do not agree to the terms of this EULA, do not install or use the SOFTWARE PRODUCT.

The SOFTWARE PRODUCT is protected by copyright laws and international copyright treaties, as well as other intellectual property laws and treaties. DEIF controllers are licensed, not sold.

1. GRANT OF LICENSE.

The SOFTWARE PRODUCT is licensed as follows:

(a) Installation and Use.
DEIF A/S grants you the right to install and use copies of the SOFTWARE PRODUCT on your computer running a validly licensed copy of the operating system for which the SOFTWARE PRODUCT was designed Windows 7, Windows 8, Windows 10.

(b) Backup Copies.
You may also make copies of the SOFTWARE PRODUCT as may be necessary for backup and archival purposes.

2. DESCRIPTION OF OTHER RIGHTS AND LIMITATIONS.

(a) Maintenance of Copyright Notices.
You must not remove or alter any copyright notices on any and all copies of the SOFTWARE PRODUCT.

(b) Prohibition on Reverse Engineering, Decompilation, and Disassembly.
You may not reverse engineer, decompile, or disassemble the SOFTWARE PRODUCT, except and only to the extent that such activity is expressly permitted by applicable law notwithstanding this limitation.

(c) Rental.
You may not rent, lease, or lend the SOFTWARE PRODUCT.

(d) Compliance with Applicable Laws.
You must comply with all applicable laws regarding use of the SOFTWARE PRODUCT.

3. TERMINATION

Without prejudice to any other rights, DEIF A/S may terminate this EULA if you fail to comply with the terms and conditions of this EULA. In such event, you must destroy all copies of the SOFTWARE PRODUCT in your possession.

4. COPYRIGHT

All title, including but not limited to copyrights, in and to the SOFTWARE PRODUCT and any copies thereof are owned by DEIF A/S or its suppliers. All title and intellectual property rights in and to the content which may be accessed through use of the SOFTWARE PRODUCT is the property of the respective content owner and may be protected by applicable copyright or other intellectual property laws and treaties. This EULA grants you no rights to use such content. All rights not expressly granted are reserved by DEIF A/S.

5. NO WARRANTIES

DEIF A/S expressly disclaims any warranty for the SOFTWARE PRODUCT. The SOFTWARE PRODUCT is provided 'As Is' without any express or implied warranty of any kind, including but not limited to any warranties of merchantability, noninfringement, or fitness of a particular purpose. DEIF A/S does not warrant or assume responsibility for the accuracy or completeness of any information, text, graphics, links or other items contained within the SOFTWARE PRODUCT. DEIF A/S makes no warranties respecting any harm that may be caused by the transmission of a computer virus, worm, time bomb, logic bomb, or other such computer program. DEIF A/S further expressly disclaims any warranty or representation to Authorized Users or to any third party.

6. LIMITATION OF LIABILITY

In no event shall DEIF A/S be liable for any damages (including, without limitation, lost profits, business interruption, or lost information) rising out of 'Authorized Users' use of or inability to use the SOFTWARE PRODUCT, even if DEIF A/S has been advised of the possibility of such damages. In no event will DEIF A/S be liable for loss of data or for indirect, special, incidental, consequential (including lost profit), or other damages based in contract, tort or otherwise. DEIF A/S shall have no liability with respect to the content of the SOFTWARE PRODUCT or any part thereof, including but not limited to errors or omissions contained therein, libel, infringements of rights of publicity, privacy, trademark rights, business interruption, personal injury, loss of privacy, moral rights or the disclosure of confidential information.